Quiz Sections

  1. Home
  2. Training
  3. GEM-C Firewolf Dedicated Fire System Certification Course Test Questions
  1. How many amps of power does the Gem-C fire Panel have onboard?
  2. What is the maximum number of NAC extenders you can have on the system?
  3. Which of the following synchronization protocols are built in?
  4. On the larger Gem-C fire systems, what is the maximum standby power can you have?
  5. The Gem-C fire Control panel is only surface mountable.
  6. The Dual Phones Lines are on a separate module.
  7. The Fire Motherboard comes with 8 zones onboard.
  8. How many Firewolf Two Wire Smokes can you put on each zone of the Fire Input Module?
  9. How many zones are used when you install a NAC Extender?
  10. How many zones are used when you install a Remote Power Supply?
  11. A Fire SLC Module can support 128 Fire SLC Devices.
  12. How many SLC modules can the Gem-C fire panel support?
  13. Using 14 Gauge wire you can run the fire SLC loop.
  14. You do not need to address the SLC modules.
  15. You can adjust the obscuration levels on our analog addressable smoke detectors.
  16. Which two devices do you need 24V Regulated Power for?
  17. You can program one panel NAC circuit for a 12v or 24v output
  18. The Fire SLC Device Address Range is from
  19. How many wireless receivers can you have on the system if you are using one SLC Module?
  20. How many wireless devices can you install on a fire system?
  21. The Gem-C-NL-Mod needs to have a Napco netlink receiver at your Central Station to work.
  22. Which version software do you need to have in order to program the Gem-C fire panel?
  23. The Master Code on the Gem-C fire Panel is reprogrammable.
  24. The EZM's on the Gem-C must be consecutively addressed.
  25. You can partition the Fire System.
  26. Which areas can the Fire System be assigned to?
  27. Which addresses can you give the SLC Modules?
  28. You can silence the horns and still have the strobes on.
  29. Which of the following can you unlock the Fire keypad with?
  30. You will lose the UL 9 Edition Rating if you install any Napco peripheral that is not listed for the Gem-C Panel.
  31. How many Fire keypads can you have on the system?
  32. How many user codes can you have on the system?
  33. Under System Options it is always necessary to have the FIM Module enabled on a Fire System.
  34. The first 8 zones in the programming are reserved for the Hardwired FIM zones.
  35. You can program RM3008 boards and OUT8 boards to follow events from the NAC output assignment tab.
  36. You can program a Fire Zone for any area.
  37. The green telephone icon is for what type of communication?
  38. The blue telephone icon is for what type of communication?
  39. You must perform an error check and clear all errors before you download the Fire Panel.
  40. You must unlock both the Fire keypad and the Quick loader software before you download to the Fire Panel.
  41. You can program cadences by zone.
  42. The system has a water flow retard time that is programmable.
  43. When programming addressable devices you must program which of the following information?
  44. When programming a wireless device you must program which of the following areas?
  45. What type of printer can be connected to the Panel?
  46. Under subscriber ID Numbers on a fire Panel the account number must be programmed at least for Area 1 and System.


Visit Our Other Sites

Napco
Alarm Lock
MarksUSA
Napco Access Pro
333 Bayview Avenue, Amityville, NY 11701 • (631) 842-9400
• Fax: (631) 789-9292 • email: salesinfo@napcosecurity.com
Copyright 2026, Napco Security Technologies, Inc. All rights reserved